If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
No matter what type of furnace you have, you’ll almost certainly need repair and maintenance services at some point. Just like any piece of machinery, furnaces can’t run error–free forever. But you don’t have to live in fear of the day your furnace breaks down either. With our heating technicians on the job, your furnace will usually be back online in no time.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
Ramsey Heating and Air Conditioning is a family-owned, hometown business located in the foothills of North Carolina. We know you have a choice when it comes to heating and cooling, so here at Ramsey HVAC we strive to be the best. We have the skills and professional experience to provide you with any heating and cooling service needs you experience. Here at Ramsey we want to provide homeowners with an honest evaluation of their home comfort system and only offer options for them that are in their best interest.
I'm very glad that I found another guy to come replace the circuit board and put it away from the water, fix the water leak, and also find and fix another impending failure. All of that was for much less than HVAC Service wanted to charge for repair or replacement. The other guy did a great repair, so I'm confident it will not break down again, but if it does, I will not call HVAC Service. Don't get suckered by their Yelp Deal.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
If your air conditioning is blowing warm air—or not working at all—it's time to call in the experts. After all, we're not just talking about an uncomfortable afternoon on a hot day: we're talking about your happiness at home, and a problem that may cause extensive damage to your system if not addressed quickly. That's why it's smart to catch problems early before they become expensive to address.
With winter on its way back to Atlanta, furnace and heating repair may not be the first thing you think about, but maybe it should be. Sure, it’s easy for us to sit here and tell you to arrange annual furnace service, but it’s only because we want to help you avoid a heating breakdown during the coldest day of the month in Atlanta. Day or night, our HVAC experts are here to ensure you have a comfortable home, and can help get your furnace back operating in almost no time.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
Cut down on energy costs and prevent damage to your furnace by addressing a gas furnace that's overactive or short cycling. Besides the need for consistently comfortable temperatures, this issue could cause long-term safety issues to your home, making it very important to address. From a faulty thermostat to a dirty filter, there are several possible causes to investigate.
Throughout the coldest months of winter—especially in North America—a heating system repair is probably not something you want on your mind, but it likely will be if you need it on a bone-chilling day. You are in luck though, because Service Experts Heating & Air Conditioning is committed to doing expert quality furnace and heat pump repair, maintenance and installation through North America. It’s our job to make sure you are left with complete comfort in your home.
Given the broad price ranges above, it's easy to recognize that the cost of your furnace repair varies drastically based on which parts need attention. As a result, it makes sense to gain a better understanding of the parts that heat your home, and how much they cost to repair. Repairing or replacing your furnace’s blower motor can cost you anywhere between $150 and $450, depending on the extent of the damage. Heat exchanger repair costs can vary greatly, from as little as $100 for a simple fix to as much as $1,200 for a full replacement. Repairing a furnace igniter will only cost you $300 at most, while flame sensor repairs generally fall between $80 to $250. The average cost to repair your Thermostat will range from $108 to $282.
We’ve earned a reputation across Portland and The Dalles for dedicated customer service. Consistently maintaining an A+ rating from the Better Business Bureau, Sky Heating & Air Conditioning meets higher standards of excellence through the little, important details that add up to a job well done. It starts with a friendly voice on the phone, and the immediate focus of our extensive resources on your requirements. From there, you can count on timely arrival, organized project management, careful cleanup, competitive pricing, and exemplary performance in every aspect of service. When you contact Sky Heating & Air Conditioning for HVAC service in The Dalles and Portland, OR, your project is always handled by a highly-trained professional, who will achieve your goals for efficiency, reliability, and sustainable home comfort.
For less than $9* per month, one of our pros will make sure your heater is ready for winter – and your air conditioner is prime for summer. The home maintenance plan also includes electrical and plumbing inspections. And that’s not all! Sign up, and you get special discounts on service, parts and labor.*The price is as low as $8.25* per month, with $99/year for each additional HVAC system.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
"I purchased a mobile home recently and the electrical was a mess. One of the circuits was down and the previous owner had wired the breaker box very strange. One outlet (on a working circuit) had an electrical fire that destroyed it. I'm a DIY guy but I haven't done much with electric before so I asked for a quote on this website. Todd called me within the hour, and we set an appointment for 2 days later. He was on time to the appointment and was able to diagnose the problem AND fix my destroyed outlet within 10 minutes (I already had a new outlet ready to be installed). What's more, he didn't even charge me for it, just said that when I was ready to fix my circuit to give him a call (I'm redoing all the plumbing right now). Todd deserves 6 stars. He is an expert at what he does, he's friendly, he's reasonable, and he's fast. Don't hesitate to contact him. I wish more technical professionals were like him."